JN0-343 Royal Pack Testengine pdf
100% Actual & Verified — 100% PASS
Unlimited access to the world's largest Dumps library! Try it Free Today!https://www.exambible.com/JN0-343-exam/
Exam Number/Code: JN0-343
Exam name: uniper Networks Certified Internet Specialist (JNCIS-ENT)
n questions with full explanations
Certification: Juniper Certification
Last updated on Global synchronizing
Youre going to get the detailed reason when you encounter issues on your JN0-343 research. Testking give you the JN0-343 uniper Networks Certified Internet Specialist (JNCIS-ENT) key points legibly within the JN0-343 dumps. All these are tremendously saving your own expenditures to get familiar with the Juniper courses.
2016 Jun JN0-343 vce
Q91. Which two steps must be performed to carry out a unified ISSU on an EX Series Virtual Chassis? (Choose two.)
A. Enable GRES and NSR, then verify that the Routing Engines are synchronized.
B. Download the new software package and copy it to both Routing Engines before the upgrade.
C. Verify that the master and backup Routing Engines are running the same software version.
D. Shut down the backup Routing Engine before the upgrade.
Q92. In the exhibit, Area 184.108.40.206 is configured as a not-so-stubby area and Area 220.127.116.11 is configured as a normal area. R5 has an export policy that causes the RIP network prefixes to be announced through OSPF. Which LSA type does R7 receive describing the RIP network prefixes?
A. Summary (Type 3)
B. ASBRSum (Type 4)
C. Extern (Type 5)
D. NSSA (Type 7)
Q93. You want STP to behave similar to RSTP.
Which three configuration settings under the [edit protocols stp] hierarchy on an EX Series switch allow this? (Choose three.)
Q94. Which command on an EX Series switch allows for the configuration of the duplex setting on multiple interfaces at the same time?
Q95. As shown in the exhibit, Switch-3 receives a superior BPDU from Switch-2 over the ge-0/0/10.0 interface. Which two statements are correct? (Choose two.)
A. Switch-2's ge-0/0/10.0 port assumes the backup role and blocking state.
B. Switch-3's ge-0/0/10.0 port assumes the designated role and forwarding state.
C. Switch-2's ge-0/0/10.0 port assumes the designated role and forwarding state.
D. Switch-3's ge-0/0/10.0 port assumes the alternate role and blocking state.
Improve JN0-343 question:
Q96. Which three steps must you complete for an aggregated Ethernet configuration on a switch? (Choose three.)
A. Define the aggregated Ethernet interface under the [edit chassis] stanza.
B. Configure the interface under the [edit protocols lacp] stanza.
C. Configure the aggregated Ethernet interface.
D. Assign physical interfaces to the aggregated Ethernet interface.
E. Configure the minimum number of links required for the bundle to be operational.
Q97. In which state is an interface placed if root-protect is enabled and a superior BPDU is received?
Q98. Router R2 is having adjacency problems with Router R1. Router R2 is stuck in ExStart state.
What is causing the problem?
A. There is a physical and data link layer problem between R1 and R2.
B. There is a misconfigured IP address on the R2 interface.
C. The hello and dead intervals on R2 do not match R1.
D. The interface MTU setting on R2 does not match R1.
Q99. You have both IPv4 and IPv6 running in your network. You are asked to migrate your IGP from IS-IS to OSPF. The network must retain OSPF connectivity between all routers.
Which statement is correct?
A. You must use OSPFv2 on all your routers.
B. You must use OSPFv3 on all your routers.
C. You must use OSPFv4 on all your routers.
D. IPv6 routers must continue to use IS-IS.
Q100. In a switched network with redundant paths, which frame does not require the implementation of a spanning tree to prevent a loop?
B. unknown MAC address
C. known MAC address
D. ARP request
see more http://www.pdfcollection.net/JN0-343-pdf.html