A Review Of Certified 300-135 exam dumps

300-135 Royal Pack Testengine pdf

100% Actual & Verified — 100% PASS

Unlimited access to the world's largest Dumps library! Try it Free Today!

https://www.exambible.com/300-135-exam/

Product Description:
Exam Number/Code: 300-135
Exam name: TSHOOT Troubleshooting and Maintaining Cisco IP Networks
n questions with full explanations
Certification: Cisco Certification
Last updated on Global synchronizing

Free Certification Real IT 300-135 Exam pdf Collection

we provide Validated Cisco 300 135 tshoot testing engine which are the best for clearing ccnp tshoot 300 135 dumps pdf test, and to get certified by Cisco TSHOOT Troubleshooting and Maintaining Cisco IP Networks. The 300 135 tshoot pdf Questions & Answers covers all the knowledge points of the real ccnp tshoot 300 135 dumps pdf exam. Crack your Cisco cisco 300 135 Exam with latest dumps, guaranteed!

P.S. Validated 300-135 practice are available on Google Drive, GET MORE: https://drive.google.com/open?id=1BNfdP-dYaYDxxYw2CbIPONm9qPz9JsvY


New Cisco 300-135 Exam Dumps Collection (Question 6 - Question 15)

Q1. The implementations group has been using the test bed to do a u2018proof-of-conceptu2019 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

Use the supported commands to isolated the cause of this fault and answer the following questions.

What is the solution to the fault condition?

A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

H. ASW2

Answer: G

Explanation:

The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.


Q2. The implementations group has been using the test bed to do a u2018proof-of-conceptu2019 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

Use the supported commands to isolated the cause of this fault and answer the following questions.

The fault condition is related to switch technology?

A. NTP

B. Switch-to-Switch Connectivity

C. Loop Prevention

D. Access Vlans

E. VLAN ACL Port ACL

F. Switch Virtual Interface

G. Port Security

Answer: D

Explanation:

The problem here is that VLAN 10 is not configured on the proper interfaces on switch ASW1.

Topic 8, Ticket 3 : OSPF Authentication

Topology Overview (Actual Troubleshooting lab design is for below network design)

u2711 Client Should have IP 10.2.1.3

u2711 EIGRP 100 is running between switch DSW1 & DSW2

u2711 OSPF (Process ID 1) is running between R1, R2, R3, R4

u2711 Network of OSPF is redistributed in EIGRP

u2711 BGP 65001 is configured on R1 with Webserver cloud AS 65002

u2711 HSRP is running between DSW1 & DSW2 Switches

The company has created the test bed shown in the layer 2 and layer 3 topology exhibits. This network consists of four routers, two layer 3 switches and two layer 2 switches.

In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.

DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.

R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the ISPu2019s network. Because the companyu2019s address space is in the private range. R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and outside (209.65.0.0/24) network.

ASW1 and ASW2 are layer 2 switches.

NTP is enabled on all devices with 209.65.200.226 serving as the master clock source. The client workstations receive their IP address and default gateway via R4u2019s DHCP server.

The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on DSW1 and DSW2.

In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.

DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.

The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the underlying IPv4 OSPF domain. Redistrution is enabled where necessary.

Recently the implementation group has been using the test bed to do a u2018proof-of-conceptu2019 on several implementations. This involved changing the configuration on one or more of the devices. You will be presented with a series of trouble tickets related to issues introduced during these configurations.

Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and solution.

Each ticket has 3 sub questions that need to be answered & topology remains same. Question-1 Fault is found on which device,

Question-2 Fault condition is related to,

Question-3 What exact problem is seen & what needs to be done for solution

=====================================================================

Client is unable to ping IP 209.65.200.241

Solution

Steps need to follow as below:-

u2711 When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4

Ipconfig ----- Client will be receiving IP address 10.2.1.3

u2711 IP 10.2.1.3 will be able to ping from R4 , R3, R2 but not from R1

u2711 Check for neighborship of ospf

sh ip ospf nei ----- Only one neighborship is forming with R2 & i.e. with R3

Since R2 is connected to R1 & R3 with routing protocol ospf than there should be 2 neighbors seen but only one is seen

u2711 Need to check running config of R2 & R3 for interface

Sh run -------------------------- Interface Serial0/0/0/0.12 on R2

Sh run -------------------------- Interface Serial0/0/0/0 on R1

u2711 Change required: On R1, for IPV4 authentication of OSPF command is missing and required to configure------ ip ospf authentication message-digest


Q3. The implementations group has been using the test bed to do a u2018proof-of-conceptu2019 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

Use the supported commands to isolated the cause of this fault and answer the following questions.

On which device is the fault condition located?

A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

Answer: A

Explanation:

On R1, we need to permit IP 209.65.200.222/30 under the access list.


Q4. Which of the following are shared distribution tree characteristics? (Choose all that apply.)

A. Memory requirements are higher for shared distribution tree than for source distribution tree.

B. Creates a tree from a central RP to all last-hop routers.

C. Uses a rendezvous point.

D. An optimal path is created between each source router and each last-hop router.

E. Place (S,G) entry in each router's multicast routing table.

F. Place (*,G) entry in a router's multicast routing to table.

Answer: C,F


Q5. Which of the following is an unlikely reason for the ARP process to fail?

A. CEF switching is disabled on the switch

B. The source device and destination device are in different VLANs

C. The VLAN is excluded from the trunk

D. The host is connected to the switch through an IP phone

E. A faulty cable from host to switch or between switches

F. The trunking encapsulation type is inconsistent on the two ends of the link

Answer: A,D


Q6. Refer to the Exhibit:

Which output is expected in the blank line for the OSPF adjacency process?

A. DOWN

B. EXSTART

C. EXCHANGE

D. LOADING

Answer: B

Explanation:

You can check the output of "debug ip ospf adj" here:


Q7. You have 2 NTP servers in your network - 10.1.1.1 and 10.1.1.2. You want to configure a Cisco router to use 10.1.1.2 as its NTP server before falling back to 10.1.1.1. Which commands will you use to configure the router?

A. ntp server 10.1.1.1 ntp server 10.1.1.2

B. ntp server 10.1.1.1

ntp server 10.1.1.2 primary

C. ntp server 10.1.1.1 ntp server 10.1.1.2 prefer

D. ntp server 10.1.1.1 fallback ntp server 10.1.1.2

Answer: C

Explanation: Preferred server

A router can be configured to prefer an NTP source over another. A preferred server's responses are discarded only if they vary dramatically from the other time sources. Otherwise, the preferred server is used for synchronization without consideration of the other time sources. Preferred servers are usually specified when they are known to be extremely accurate. To specify a preferred server, use the prefer keyword appended to the ntp server command. The following example tells the router to prefer TimeServerOne over TimeServerTwo:

Router#config terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#ntp server TimeServerOne prefer Router(config)#ntp server TimeServerTwo

Router(config)#^Z

Reference: Hardening Cisco Routers By Thomas Akin February 2002 0-596-00166-5, Chapter 10, NTP.


Q8. The implementations group has been using the test bed to do a u2018proof-of-conceptu2019 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services,

NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

Use the supported commands to isolated the cause of this fault and answer the following questions.

The fault condition is related to which technology?

A. NTP

B. IP DHCP Helper

C. IPv4 EIGRP Routing

D. IPv6 RIP Routing

E. IPv4 layer 3 security

F. Switch-to-Switch Connectivity

G. Loop Prevention

H. Access Vlans

I. Port Security

J. VLAN ACL / Port ACL

K. Switch Virtual Interface

Answer: J

Explanation:

On DSW1, VALN ACL, Need to delete the VLAN access-map test1 whose action is to drop access-list 10; specifically 10.2.1.3


Q9. The implementations group has been using the test bed to do a u2018proof-of-conceptu2019 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241

address.

Use the supported commands to isolate the cause of this fault and answer the following question.

The fault condition is related to which technology?

A. NTP

B. IP DHCP Server

C. Ipv4 OSPF Routing

D. Ipv4 EIGRP Routing.

E. Ipv4 Route Redistribution.

F. Ipv6 RIP Routing

G. Ipv6 OSPF Routing

H. Ipv4 and Ipv6 Interoperability

I. Ipv4 layer 3 security.

Answer: B

Explanation:

On R4 the DHCP IP address is not allowed for network 10.2.1.0/24 which clearly shows the problem lies on R4 & the problem is with DHCP


Q10. The implementations group has been using the test bed to do a u2018proof-of-conceptu2019 that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble

ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.

Use the supported commands to isolated the cause of this fault and answer the following questions.

On which device is the fault condition located?

A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

H. ASW2

Answer: G

Explanation:

port security needs is configured on ASW1.


100% Up to date Cisco 300-135 Questions & Answers shared by Certifytools, Get HERE: https://www.certifytools.com/300-135-exam.html (New 156 Q&As)